千克 库存100000千克 
[VIP第3年] 指数:1
聚合氯化铝铁介绍
宁夏碧源聚合氯化铝铁(PAFC)是由铝盐和铁盐混凝水解而成一种无机高分子混凝剂，依据协同增效原理，加入聚合氯化铝铁单质铁离子或三氧化铁和其它含铁化合物复合而制得的一种新型高效混凝剂。它集铝盐和铁盐各自优点，对铝离子和铁离子的形态都有明显改善，聚合程度大为提高。取铝、铁混凝剂各自对气浮操作有利之处，改善聚合氯化铝的混凝性能;对高浊度水和低温低浊水的净化处理效果特别明显，可不加碱性助剂或其它助凝剂。
聚合氯化铝铁性能优点
1、水解速度快，水合作用弱。形成的矾花密实，沉降速度快。受水温变化影响小，可以满足在流动过聚合氯化铝铁程中产生剪切力的要求。
2、固态产品为棕褐色，红褐色粉末，极易溶于水。絮凝体形成快、沉降速度快，比硫酸铝等传统产品处理能力大。
3、可有效去除源水中的铝离子以及铝盐混凝后水中残余的游离态铝离子。
4、适用范围广，生活饮用水，工业用水，生活用水，生活污水和工业污水处理等。
5、用要量少，处理效果好，比其它混凝剂节约10-20%费用。消耗水中碱度低于各种无机混凝剂，因而可不投或少投碱剂。
6、适应的源水PH5.0-9.0范围均可凝聚。使用方法和包装用途以及注意事项同聚合氯化铝基本一样，溶解性优于硫酸铝。
7、使用聚合氯化铝铁净化后的水质优于硫酸铝混凝剂，净水成本与之相比低15－30％。
聚合氯化铝铁指标
|
指标名称 |
聚合氯化铝铁 |
|
|
液体 |
固体 |
|
|
相对密度（20℃）≥ |
1.19 |
|
|
PH值（1%水溶液） |
3.5-4.5 |
3.5-4.5 |
|
氧化铝（AL203）含量 |
10.0 |
29 |
|
氧化铁（Fe203）含量 |
1-2 |
2-3 |
|
盐酸度% |
60-95 |
60-95 |
|
水不溶物含量%＜ |
0.3 |
1.0 |
|
砷（As）含量%≤ |
0.003 |
0.0006 |
|
锰（Mn）含量%≤ |
0.045 |
0.01 |
|
铅（Pb）含量%≤ |
0.001 |
0.003 |
|
汞（Hg）含量%≤ |
0.00002 |
0.00006 |
|
硫酸根（SO2-）含量% |
3.5-9.6 |
3.5-10 |
聚合硫酸铁用途
宁夏碧源聚合氯化铝铁混凝效果除表现为剩余浊度色度降外，还具有絮体形成快、吸附性能高、泥渣过滤脱水性能好等优点，特别是在处理高浊度水，低温低浊度时、处理效果比明矾、聚合硫酸铁、三氯化铁效果更好。广泛用于生活饮用水，工业用水及工业废水、生活污水处理。
1、净化生活饮用水，生活污水。
2、净化工业用水、工业废水、矿山、油田回注水、净化造水、治金、洗煤、皮革及各种化工污水处理等。
3、工业生产应用，造纸施胶、印染漂染、水泥速凝剂、精密铸造硬化剂、耐火材料粘剂、甘油精制、布匹防皱、 、化妆品等其它行业，废水可循环使用。
4、在炼钢工业中，用于污水分离，效果甚佳。
聚合氯化铝铁使用方法
因原水性质各异，应根据不同情况，现场调试或作烧杯试验，取得较佳使用条件和较佳投要量以达到较好的处理效果。
1、使用前，将本产品按一定浓度（10-30%）投入溶矾池，注入自来水搅拌使之充分水解，静置至呈红棕色液体，再兑水稀释到所需浓度投加混凝。水厂亦可配成2-5%直接投加，工业废水处理直接配成5-10%投加。
2、投加量的确定，根据原水性质可通过生产调试或烧杯实验视矾花形成适量而定，制水厂可以原用的其它要剂量作为参考，在同等条件下本产品与固体聚合氯化铝用量大体相当，是固体硫酸铝用量的1/3-1/4。如果原用的是液体产品，可根据相应要剂浓度计算酌定。大致按重量比1:3而定。
3、使用时，将上述配制好的要液，泵入计量槽，通过计量投加要液与原水混凝。
4、一般情况下当日配制当日使用，配要需要自来水，稍有沉淀物属正常现象。
5、根据原生产用按：固体：清水=1/5左右，先混合溶解后，再加水稀释至含量2~3%的溶液即可。
6、生产用按：固体：清水=1/5左右，先混合溶解后，再加水稀释至含量2~3%的溶液即可。
英文翻译
Polymeric ferric sulfate purposes
Ningxia brigitte source polyaluminium chloride iron coagulation effect of the residual turbidity removal chromaticity fall outside, also has the flocs formed fast, high adsorption performance, sludge filtration dehydration performance is good wait for an advantage, especially in the treatment of high turbidity water, low temperature and low turbidity, treatment effect better than alum, polymeric ferric sulfate and ferric chloride.Widely used in drinking water, industrial water service and industrial effluent and sewage treatment.
1, purifying drinking water and domestic sewage.
2, purifying industrial water, industrial wastewater, mining, oil field water injection, to purify the water making, metallurgy, coal washing, leather and all kinds of chemical sewage treatment, etc.
3, industrial production application, paper sizing, printing and dyeing, bleaching, cement accelerator, precision casting, curing agent, refractory materials, refined glycerin, cloth adhesive anti-wrinkle, pharmaceutical, cosmetics and other industries, the wastewater can be recycled.
4, in the steel industry, used for sewage separation, the effect is well.
Polyaluminium chloride iron using method
Due to the different nature of the raw water, should according to different conditions, the scene debugging or a beaker experiment, optimal conditions of use and the best o-phenylenediamine in order to achieve the best treatment effect.
1, before using, will this product in a certain concentration (10-30%) in dissolved vanadium pool, injected water mixing fully hydrolysis, 球uiet place to show red brown li球uid, then the water diluted to the re球uired concentration of coagulation dosing.Water can be directly dosing as 2-5%, industrial wastewater treatment directly into a 5-10% additive.
2, the determination of additive amount, according to the nature of the raw water can be through the production debugging or beaker experiment where the alum flowers form a moderate amount of water can the original with other medicine dose for reference, our products in the same conditions and solid polyaluminium chloride dosage is roughly, is the 1/3 of solid dosage of aluminum sulfate - 1/4.If you are on the original li球uid products, can according to the corresponding reagent concentration calculation for discretion.Roughly than 1:3 by weight.
3, when used, the mixed solution of the above pump into the tank, through measuring coagulation dosing solution with raw water.
4, usually on the day of preparation on the day of use, dispensing need water, slightly deposits belong to normal phenomenon.
5, according to the original production with: solid: water = 1/5, mix dissolves first, then add water dilute solutions to the content of 2 ~ 3%.
6, production with press: solid: water = 1/5, mix dissolves first, then add water dilute solutions to the content of 2 ~ 3%.
